Reprographic System & Supplies

Pneumatic nick grinder

developed especially for grinding nicks in cutting dies. Pneumatic drive for high performance. The damaging of the rubber during grinding is prevented, performance of the diecutter is optimized. simplified positioning for setting the nicks
Available grinding wheel size: 50x8mm or 50x10mm Grinding Wheel Thickness: 0.2mm,0.3mm,0.4mm,0.5mm,0.6mm,0.7mm,0.8mm,0.9mm,1.0mm,1.2mm,1.5mm,2.0mm.

Product Parameter

Manual Instructions1.Check the air source, air pressure stable or not 2.Check the machine screws etc. 3.Change the grinding wheel according to needs, adjust the depth valve(If not use high precision position, pls lock the depth valve to the rock bottom position, which will do the nick grinding jobs according to the pressure power) 4.Wear gloves, protective glass, masks 5.Connect to air source( suggest to hang up the air hose) 6.Pls drop 3 drops pneumatic oil to the air inlet, plug in the air hose. Rotate to right to open the grinder. Then slowly idle for a few seconds, rotate to left to close 7.Put the wooden die cutting board smoothly on the table(suggest not to use sponge rubber before nick grinding, as resistance increases) 8.Rotate to right to open the grinder, increase the speed. Use thumb and first finger to hold the machine when the rotation speed gets stable. Then put the machine in the front side of the steel rules, move it to the grinding position(use wheels to adjust the position) and gently press the machine to start nicking. Move stably in turn. Pay attention that must gently press and handle 9.After finish the nicking job, rotate to left to close. Unplug the air hose and use 3 drops pneumatic oil to the air inlet, then plug to the air hose and open the grinder to idling for a few seconds. After that close the air source, clean the machine body and keep in proper position  

Die Cutting Rule Puller

Easily solve the problem of blade extraction
The rule puller is a post-process product in the printing industry, dedicated to the removal of die cutters/rigid wires that need to be replaced on the knife board

Basic parameters
Function: Help people to pull die cutter/steel wire
Including: 1 pair of standard type (or: thin type)
Draw a knife nozzle: flat mouth
Draw knife thickness: 2PT-3PT
Drawing height: 23mmh or above
Template height:15-18mm

 

Product details  

 

Precautions for the use of knife puller
1. The rule puller is a manually operated tool,through which the die cutter/steel wire can be pulled out vertically
2. Use a puller to replace the die cutter/steel wire, so as to ensure that the gap will not widen when the knife is pulled, which will cause it to be recycled
3. Using a puller can improve work efficiency,ensure the safety of operators, and avoid work injuries caused by improper use of employees

Product Advantage

 

Features

1.Rule Puller can be flexibly removed to accommodate different knife templates;
2.When the knife is pulled,the palm is away from the die cutter,which can effectively reduce the work injury;
3.The cutter nozzle is economical and durable and can be easily replaced;
4.Easy to operate, suitable for left or right hand operation;
5.User-friendly design makes the operation more comfortable and safe. 

6.The cutter is designed with a special lever principle to ensure the vertical pull of the knife while ensuring the safety of the personnel.

Additional Information:

• Delivery Time: READY STOCK

Die Cutting Plates- 1mm Available for All Automatic Die Punching Machine.

Application:

1.  First arrange the carton boards which needs to be cleaned, make sure 

all edges flushed. Before running the machine, please make sure there are cuts on the four edges of the carton boards. The distance of each cuts should be adjusted according to different sizes of boards.
Makes breakpoints between boards and waste edges, the margins should be more than 5mm.

2.  Applicable Paper Range: 200-500gsm cartons, single/double corrugated boards and laminated cartons.

 

Description:

Free Speed (R.P.M)  : 2500RPM
Air Motor Consumption :12CFM
Chain Material :SK9,High-frequency quenching HRC60 degree
Air hose size (mm)  : 8*12
Net Weight  : 4KGS

Additional Information:

• Delivery Time: READY STOCK
• Packaging Details: FREIGHT AT ACTUALS GST AT ACTUALS INSTALLATION CHARGES EXTRA